- Compatible With: G935A (AT&T), G935F, G935P (Sprint), G935V (Verizon), G935T (T-Mobile), G935R4 (US Cellular), G935W8
For Samsung Galaxy S7 Edge G935/G935F/G935A/G935V/G935P/G935T/G935R4/G935W8 LCD Digitizer Assembly Replacement - Black - Without Any Logo - Grade S+
This item includes the following parts:
1. LCD Screen;
2. Digitizer Touch Screen.
This item does NOT include Front Housing.
Notes: please test the functionality of this item before installation.
Version: Without Any Logo
Screen Size: 5.5 inches
Resolution: 1440 x 2560 pixels, 534 ppi pixel density
Material: Super AMOLED capacitive touchscreen, 16M colors
Protective Material: Corning Gorilla Glass 4
Compatibility: Samsung Galaxy S7 Edge
● This Galaxy S7 Edge LCD assembly does NOT include the frame or front housing adhesive.
● This Galaxy S7 Edge LCD and digitizer assembly is a brand new original replacement.
● The Galaxy S7 Edge LCD assembly is available in differnt colors and versions, this is the Black one without any logo. And we also provide Silver and Gold one with logo.
● This screen replacement is compatible with all Samsung Galaxy S7 models.
How to Install / Tips:
● Special repairing tools are required for assembling or disassembling.
● The waterproof function will lose once the Galaxy S7 Edge LCD assembly was replaced.
● Handle the vulnerable and fragile flex cable ribbon carefully.
● Please try to handle the repair or replacement work in a dry and dust free environment without direct sunlight.
● The installation of any new part should be done by a qualified person. ETS is not responsible for any damage caused during installation.
Shut down the Samsung Galaxy S7 Edge then remove the SIM card tray.
Heat up the back the S7 edge(until it’s too hot to touch).
Apply the suction cup to the back cover of the S7 edge.
Pry the edge of the S7 edge back cover a little bit to insert the thin metal spudger.
Slide away the metal spudger a little bit then insert some business cards/playing cards to do the rest.
Once the back cover has been released, undo the 12 Phillips screws holding the rear housing.
Use the plastic separation tool to separate the top plastic bracket then remove the wireless charging pad.
Disconnect the battery cable, power cable, display cable and the volume button cable.
Use a pair of tweezers to remove the loud speaker module.
Pop off all the antenna cables and the fingerprint scanner cable.
Disconnect the earphone connector, front facing camera connector and the proximity and light sensor connector.
Lift up the motherboard then disconnect the charging port connector.
Disconnect and remove the rear facing camera.
Heat up to the adhesive underneath the battery, then use the metal spudger to lift it up (slowly and carefully).
Undo 3 screws holding the charging port then take out the headphone jack.
Step 16. Use the cotton swab to withstand the proximity and light sensor hole, then apply some heat around the top front glass panel.
VERY gently press the screen assembly a little bit to leave a gap between the screen and the front housing, then very slowly insert the thin metal separation tool (don’t insert it too deep, when the top of the separation tool reaches the hole, that’s far enough).
Insert a thin plastic film/business cards/playing cards from the gap you created just now, then slowly and gently slide it through the edge.
Use a soft/plastic tool (we used our fingernails LOL) to withstand the open gap (Keep the angle of the gap, DON’T widen it too big).
Use a pair of tweezers to drag out the black adhesive around the edges little by little, two sides alternately (Apply heat to the edge when it’s cooled down).
After all the adhesive has been cleared, carefully open up the screen from one side.
Test the new screen works or not before the installation.
Apply the 3M adhsive around the edges of the front housing, then reassemble the screen.
Put the head phone jack back again.
Reconnect the rear facing camera.
Reconnect the motherboard with the charging port then put it back into the position (avoid those cables and connectors).
Reconnect the power cable, display cable, earphone connector, proximity and light sensor connector and the volume button cable.
Reconnect the fingerprint scanner connector and 2 antenna connectors.
Reconnect the front facing camera.
Put back the battery.
Reassemble the loud speaker module.
Reconnect the battery.
Re-put the wireless charging pad and the top plastic bracket.
Re-assemble all the screws holding the rear housing.
Put some 3M double adhesive around the edges then reassemble the back cover.
Customer also bought
Mobile Accessories Recommended